(Mexico)
Provided information in the table shows your child-restraint system suitability for various seating position. For installation suitability of other manufacturer child-restraint system, carefully consult the manufacturer's instructions which accompany the child-restraint system.
When installing a child-restraint system, the following points must be observed:
If the child-restraint system does not fit into the seatback because of the head restraint, adjust the head restraint or remove the head restraint so that the child-restraint system fits into the seatback. However, when installing a backless booster seat, always install the vehicle head restraint to the seat where the backless booster seat is installed.
Refer to Head Restraints (Search).
When installing a child-restraint system to the rear seat, adjust the front seat position so that the front seat does not contact the child-restraint system.
Refer to Seat Operation (Search).
When installing a child-restraint system came equipped with a tether, remove the head restraint.
Refer to Head Restraints (Search).
LATCH lower anchor-secured child-restraint systems
When installing a child-restraint system to the rear seat, refer to the child-restraint system manufacturer's instructions and the Using LATCH Lower Anchor (Search).
Mass group |
Size Class |
Fixture |
Vehicle LATCH positions |
---|---|---|---|
Second-row seat (Outboard) |
|||
Carrycot |
F |
ISO/L1 |
X |
G |
ISO/L2 |
X |
|
(1) |
X |
||
GROUP 0 Up to 10 kg (up to 22 lb) |
E |
ISO/R1 |
IL |
(1) |
X |
||
GROUP 0 Up to 13 kg (up to 29 lb) |
E |
ISO/R1 |
IL |
D |
ISO/R2 |
IL |
|
C |
ISO/R3 |
IL |
|
(1) |
X |
||
GROUP 1 9 kg ― 18 kg (20 lb ― 40 lb) |
D |
ISO/R2 |
IL |
C |
ISO/R3 |
IL |
|
B |
ISO/F2 |
IUF |
|
B1 |
ISO/F2X |
IUF |
|
A |
ISO/F3 |
IUF |
|
(1) |
X |
||
GROUP 2 15 kg ― 25 kg (33 lb ― 55 lb) |
(1) |
X |
|
GROUP 3 22 kg ― 36 kg (48 lb ― 79 lb) |
(1) |
X |
|
(1) For the CRS which do not carry the ISO/XX size class identification (A to G), for the applicable mass group, the car manufacturer shall indicate the vehicle specific LATCH child-restraint system(s) recommended for each position.
Key of letters to be inserted in the above table:
IUF = suitable for LATCH forward child-restraints systems of universal category approved for use in this mass group.
IL = suitable for particular LATCH child-restraint systems (CRS).
These LATCH CRS are those of the “specific vehicle”, “restricted” or “semi-universal” categories.
X = LATCH position not suitable for LATCH child-restraint systems in this mass group and/or this size class.
When installing a child-restraint system, the following points must be observed:
Always remove the head restraint before installing a child-restraint system. However, when installing a backless booster seat, always install the vehicle head restraint to the seat where the backless booster seat is installed. In addition, always use a tether strap and attach it securely. Refer to Head Restraints (Search).
When installing a child-restraint system to the second-row seat, adjust the front seat position so that the front seat does not contact the child-restraint system. Refer to Seat Operation (Search).
i-Size child-restraint systems
An i-Size child-restraint system can be installed to the specified seat as follows:
Front passenger seat |
Rear seat (outboard) |
Rear seat (center) |
|
---|---|---|---|
i-Size child-restraint systems |
X |
X |
X |
Key of letters to be inserted in the above table:
X = Seating position not suitable for i-Size “universal” child-restraint systems.
An i-Size child-restraint system refers to a child-restraint system which has acquired i-Size category certification for the UNECE 129 regulation.
Seat belt-secured child-restraint systems
System group |
Age group |
Weight group |
Child-restraint system type |
Front passenger seat |
Second-row seat (outboard) |
Second-row seat (center) |
Third-row seat (outboard) |
---|---|---|---|---|---|---|---|
GROUP 0 |
Up to about 9 months old |
Up to 10 kg (up to 22 lb) |
Infant seat |
X |
U |
U*2 |
U |
GROUP 0 |
Up to about 2 years old |
Up to 13 kg (up to 29 lb) |
Infant seat |
X |
U |
U*2 |
U |
GROUP 1 |
About 8 months to 4 years old |
9 kg ― 18 kg (20 lb ― 40 lb) |
Child seat |
L*1 |
U |
U*2 |
U |
GROUP 2 |
About 3 to 7 years old |
15 kg ― 25 kg (33 lb ― 55 lb) |
Booster seat |
L*1 |
U |
U*2 |
U |
GROUP 3 |
About 6 to 12 years old |
22 kg ― 36 kg (48 lb ― 79 lb) |
Booster seat |
L*1 |
U |
U*2 |
U |
Key of letters to be inserted in the above table:
U = Suitable for “universal” category restraints approved for use in this mass group.
L = For the child restraint systems categorized in this weight group, consult an Authorized Mazda Dealer. Regarding child restraint systems which can be installed, refer to the accessories catalog.
X = Seat position not suitable for children in this mass group.
A Mazda genuine child restraint system can be installed in the forward-facing position.
When a child-restraint system is installed to the rear center seat, do not seat occupants in the rear left outboard seat position.
When installing a child-restraint system, the following points must be observed:
(Second-row seat)
Always remove the head restraint before installing a child-restraint system. However, when installing a backless booster seat, always install the vehicle head restraint to the seat where the backless booster seat is installed. In addition, always use a tether strap and attach it securely. Refer to Head Restraints (Search).
When installing a child-restraint system to the second-row seat, adjust the front seat position so that the front seat does not contact the child-restraint system. Refer to Seat Operation (Search).
When installing a child-restraint system to the third-row seat, adjust the second-row seat position so that the second-row seat does not contact the child-restraint system. Refer to Seat Operation (Search).
(Except Mexico)
Please comply with the legal regulations concerning the use of child-restraint systems in your country.
Page top